A LEADING AUTOMOTIVE ABS PUMPS REPAIR

Suzuki Common ABS Pump (ESP Fault) – Brake Pressure Sensor Switch Failure

27 Nov, 14

Suzuki Common ABS Pump (ESP Fault) – Brake Pressure Sensor Switch Failure

Suzuki C1028 Brake Pressure Sensor RepairSuzuki Brake Pressure Sensor Problems
The MK60 ATE Teves ABS pump is fitted to a wide variety of vehicles from all makes of manufacture and includes the Suzuki group vehicles. This type of ABS pump has an internal brake pressure sensor manufactured inside the unit is commonly known for it’s pressure sensor fault and is very expensive to replace. Earlier ABS pumps never had this fault because the pressure sensor was never before fitted inside the ABS pump – but these new type of ABS units are failing all day long and it’s a major design fault with all internal pressure sensor units.

How To Detect The Suzuki Brake Pressure Sensor Fault
When the pressure sensor has failed on the Suzuki ABS system, the traction control light will be illuminated and sometimes the ABS light as well. The traction control (ESP) button may also be illuminated and pressing the button will have no affect.

Common DTC Fault Code Associated With This Fault
C1028 – Brake pressure Sensor Circuit defective. – Present.

Common Suzuki Vehicles Affected With The Pressure Sensor Faults
Below we have compiled a short list of vehicles we have found fitted with the MK60 ATE ABS pump from our own experiences of units being sent in to our workshops on a daily basis for rebuilds and exchange.
[table “39” not found /]

Common Suzuki ABS Part Numbers Affected
Below are the most common part numbers coming in every day to our workshop. We receive 100’s of units from all makes of vehicles each week for repair and replacement so don’t worry if your part number is not listed.
[table “40” not found /]

If your Suzuki has the dreaded Brake Pressure Sensor fault then you probably already have had a scary quote from a dealer of £1200+. Even second hand used parts are not cheap and require additional coding / programming. Neither of these options are recommended because it doesn’t fix the root cause of the problem and you will be just waiting on the day for it to fail again.

My Brake Pressure Sensor Has Fail – How Can SINSPEED Help Me?
Instead of just replacing the unit with a like-for-like part or repairing the ABS with a standard like-for-like pressure sensor as most workshops are currently offering. Sinspeed will take your unit and modify it to ensure never again over heats and then replace the pressure sensor with an uprated component. The uprated pressure sensor is guaranteed to last the lifetime of the vehicle and all components used by Sinspeed during the remanufacturing process are brand new OEM quality parts to ensure that each & every rebuilt ABS pump meets and exceeds OE specifications.

All of our rebuilt ABS units come with a Lifetime warranty and will not require programming. Our ABS pumps are self calibrating – making them fully plug & play!

Why Modify The Unit? – Why Not Just Replace The Damaged Part?
All cars prior to the MK60 ATE ABS unit had the pressure sensor fitted externally and never failed.

If we fit a standard part inside the pump it will still have the design fault it was manufactured with and although we can put a warranty on the unit and replace the sensor each time it fails (because they are cheap as chips to buy) you will still be left inconvenienced by having to remove the unit each time it fails and pay for the labour each time. We rework the original design and ensure that our modified units are rebuilt to last.

SAFETY WARNING!!
There have been rumours of people and/or companies trying to repair these units and in some cases imitate our work. Please understand that although the ESP system is not absolutely crucial, modifying the ABS controller / pump in any way (without superior extensive knowledge) in the technology of advanced braking systems and electronic control modules, you will be risking the life of others. Please do not attempt to repair these units yourself and please do not offer such services to trade or the general public. We have been in business since 1972 as a group company and all our parts, services are fully tested before leaving the workshop. All units are thoroughly tested on specific specialist equipment to ensure maximum quality. Our ESP Fault Modifications come fully approved and as far as we’re aware, there is no other company out there that can successfully repair these units and completely remove the defective state.

If you have a vehicle with the Brake Pressure Sensor ESP Fault then give us a call on 0844 847 9999.

Tags : 000403296D1, 06210208854, 06210952003, Suzuki Brake Pressure Sensor Problems, Suzuki C1028 Pressure Sensor Fault Code.
77 thoughts on “Suzuki Common ABS Pump (ESP Fault) – Brake Pressure Sensor Switch Failure
    • Hi James

      Thanks for the enquiry,

      We’ve sent you an email with full pricing and information for the Suzuki Swift pressure sensor fault.

      Kind Regards

      Jason
      SINSPEED

  • hi i have a suzuki splash 1.2 58 plate with error code C1028 AND C1078
    can you give me a price to repair it please
    also is it realy just a matter of taking the old one off and putting the unit back on after you repair it and just bleeding the brakes in the normal way
    And do all the dash lights work as they should after the mod ?
    thanks nige.

    • Hi Nigel

      Thanks for the enquiry,

      We’ve sent you an email with full pricing & information.

      Kind Regards

      Jason
      SINSPEED

  • Hi, I have a Suzuki Swift 2009 (59) SZL 1300cc which has been diagnosed with the ABS Pump problem. Can you give me a price for this to be fixed, what is the normal turnaround for this process and is the unit straight forward to refit.

    Many Thanks,
    Robert.

    • Hi Robert

      Thanks for the enquiry,

      We’ve sent you an email with full information and pricing.

      Kind Regards

      Jason
      SINSPEED

  • Hi,
    I have a Vauxhall Astra H 2007 with fault code C0131-00 & C0131-5A part number 13 246 535
    can you please come back to me with repair costs.
    Regards Rob

    • Hi Rob

      Thanks for the enquiry,

      We’ve sent you an email with full pricing & information.

      Kind Regards

      Jason
      SINSPEED

  • Hi, my 2007 Suzuki swift sport has the ESP, ABS and traction lights on. Am guessing it’s the sensor. Could I get a price for the repair?
    Cheers

    • Hello Jack,

      Thank you for your enquiry,

      We have sent you over an email with full pricing and information.

      Kind Regards

      Jason
      SINSPEED

  • Hi I have a Suzuki splash 2004 model with ESP light on I think it’s the ABS pump that’s faulty how much would it cost to have it repaired.
    Marj.

    • Hello Marj,

      Thank you for your enquiry,

      We have sent you over an email with full pricing and further information.

      Kind Regards

      Jason
      SINSPEED

  • Good day to you, I have “Service ESP System” warning that appeared on my 2011 Suzuki Grand Vitara Prestige 4X4. It was diagnosed as ABS pump / module failure – Code DTC C1601. The part number on the unit is:
    06 2109 – 6000.3 & 06 2619 – 37201.
    What would you charge to repair this unit and also do I only have to remove the module? One more issue. I am based in Melbourne, Australia.

    • Hello Pran,

      Thank you for your enquiry.

      I have sent over an email for further information regarding the issues with your Suzuki ABS Pump.

      Kind Regards

      Jason
      Sinspeed

    • Hello Paul,

      Thank you for your enquiry,

      I have sent over an email with pricing and further information regarding the repair of your Suzuki Brake Pressure Sensor.

      Kind Regards

      Jason
      Sinspeed

    • Hello Br. Mathias,

      Thank you for your enquiry,

      I have sent over an email with further information regarding the repair of your Suzuki Swift Brake Pressure Sensor.

      Kind Regards,

      Jason
      Sinspeed

  • Hi, i have a Suzuki Swift 2011 1.3 Diesel.
    I have the same error although my engine management light came on at the same time.
    Please send me some price info.

    Rgrds

    • Hello Stewart,

      Thank you for your enquiry,

      I have sent over an email with pricing & further information regarding the repair of your Suzuki Swift Brake Pressure Sensor.

      Kind Regards,

      Jason
      Sinspeed

  • Have a faulty module on my 2008 1.9l diesel vitara. Part numbers on pump module are 06.2109-5329.3 06.2619-3142.1 06.2102-1029.4 and is made in Japan. I am in Australia.

    • Hello Craig,

      Thank you for your enquiry,

      I have just sent over an email now with pricing & further information regarding the repair of the ABS Pump on your Suzuki Vitara.

      Kind Regards,

      Jason
      Sinspeed

    • Hello Ronnie,

      Thank you for your enquiry,

      I have sent over an email with pricing as well as further information regarding the ABS ESP Pump Repair on your Suzuki Splash.

      Kind Regards,

      Jason
      Sinspeed

    • Hello Cedric,

      Thank you for your enquiry,

      I have just sent over an email now with further information regarding your Suzuki Grand Vitara ESP Repair.

      Kind Regards,

      Jason
      Sinspeed

  • Hi Jason,
    Following all the inquiries you’ve had about the ESP/ABS warning light coming on I have a 2010 Suzuki Alto with an intermittent fault. Could you advise me of the pricing for a replacement part. Thanks
    kind regards
    Mike Spencer-Hicken

    • Hello Mike,

      Thank you for your enquiry,

      I have just sent over an email for further information regarding the ABS / ESP Repair on your Suzuki Alto.

      Kind Regards,

      Jason
      Sinspeed

    • I too have an issue with the ESP/ABS warning light coming on I have a 2010 Suzuki Alto Had Suzuki run a diagnostic on it which they reported had multiple codes stored relating to ABS module, leading to an internal fault in the ABS module,. Could you advise me of the pricing for a replacement part. I am located in Melbourne, Australia, Thanks
      & regards Brian

      • Hi Brian

        Thanks for the enquiry,

        Sounds like yours may have more than just the common pressure sensor fault. Either way we should still be able to fully bench test and repair the unit and get you back up and running again. I’ve sent you an email with full pricing and information.

        Kind Regards

        Jason
        SINSPEED

    • Hello Juho,

      Thank you for your enquiry,

      I have just sent over an email with pricing and further information regarding an ABS / ESP Repair on your Suzuki Grand Vitara.

      Kind Regards,

      Jason
      Sinspeed

  • Possible my Suzuki swift has this problem my abs light came off went off now my car won’t start could u tell me if you think it’s the sensor pad and how much would cost.

    • Hello Tricia,

      Thank you for your enquiry,

      I have just sent over an email with pricing and further information regarding an ABS / ESP Repair on your Suzuki Swift.

      Kind Regards,

      Jason
      Sinspeed

  • I have an abs unit that has a malfunction in the pump (leaking) according to the mechanic. The specs are ATE 06. 2109-0568. 3 and 06. 2102 – 0385.4 the car is a Suzuki swift 2006 model 1300cc. Could you tell me the pricing of P&P from Greece Corfu and rebuild/repair.
    Thank you

    • Hello John,

      Thank you for your enquiry,

      I have just sent over an email for further information regarding the ABS ESP Brake Pressure Sensor Fault you are experiencing with your Suzuki Swift.

      Kind Regards

      Jason
      SINSPEED

  • while diving my 2008 Suzuki ESCUDO, ESP, ABS and Park Brake lights on dash board illuminated. Can you offer an estimated cost of replacement parts.

    • Hello Leroy,

      Thank you for your enquiry,

      I have just sent over an email now for further information regarding the ESP faults you are experiencing with your Suzuki Escudo.

      Kind Regards,

      Jason
      Sinspeed

    • Hello Terry,

      Thank you for your enquiry,

      I have just sent over an email now with pricing and further information regarding the repair of your Suzuki ABS Module.

      Kind Regards,

      Jason
      Sinspeed

    • Hi Georgios

      Thanks for the enquiry,

      We have sent you an email with pricing and information including our address details.

      Kind Regards

      Jason
      SINSPEED

  • Hi, please can you tell me if this ESP/ABS problem affects the Suzuki 1.0 splash,every thing I’ve read seems to point only to the 1.2 Suzuki splash, Your reply most appreciated, Thanks Steve

    • Hello Steven

      Thank you for your enquiry,

      I have sent you an email now with some further information. Please reply to the email with the part numbers and we will be able to confirm if it is repairable.

      Kindest Regards

      Jason
      Sinspeed

  • I have a suzuki swift sport 08 vvt

    The esp light has come on and was just wondering how much it costs for the abs unit to be replaced for sinspeed

    • Hi Jack

      Thanks for the enquiry,

      We’ve sent you an email with full pricing and information.

      Kind Regards

      Jason
      SINSPEED

    • Hi Michael

      Thanks for the enquiry,

      We’ve sent you an email with full pricing and information regarding the C1028 Brake Pressure Sensor fault on your Suzuki Swift Sport.

      Kind Regards

      Jason
      SINSPEED

  • I have error code C1044 – Cut-off solenoid No. 2 malfunction

    Can you please send me piricing information, as well as shipping details (I am based out of Panama)

    Thank you,
    Rodrigo

    • Hi Rodrigo

      Thanks for the enquiry,

      We’ve sent you an email with pricing and information.

      Kind Regards

      Jason
      SINSPEED

    • Hi Martin

      Thanks for the enquiry,

      We’ve sent you an email with pricing and information on the testing and repair service for your Suzuki Grand Vitara ABS module.

      Kind Regards

      Jason
      SINSPEED

  • Hiya I have this fault on my suzuki Swift sport 2007 the fault codes are as follows C1028 – C1018 can you please quote me for them sperately and combined thanks in advance

    • Hi Richard

      Thanks for the enquiry,

      We have sent you an email with full pricing and information – however, the code C1018 will relate to the brake fluid reservoir sensor so I would advise checking that first to ensure the sensor and wiring are okay. It may be that the sensor is faulty and needs replacing which will then just leave you with the C1028 code to be repaired by us.

      Kind Regards

      Jason
      SINSPEED

  • Hi. My 2007 Suzuki Grand Vitara Xsport was just in the shop for the ESP light on, the mechanic said it was the sensor inside the ABS pump – the part is listed at $2377.00. I am in the United States – are you able to provide this service to those outside of the UK and what would it cost.

    • Hi Dave

      Thanks for the enquiry,

      We can definitely provide our services to you in the US and in fact we help customers all over the world. I have sent you an email with full pricing and information.

      Kind Regards

      Jason
      SINSPEED

  • Hi, i have a 2006 suzuki swift sport with the abs light illuminated on the dash,how much does it cost to get fixed?

    • Hi Michael

      Thanks for the enquiry,

      We have sent you an email with full pricing and information for the test and repair of your Suzuki Swift ABS pump.

      Kind Regards

      Jason
      SINSPEED

  • Hi, I have a 2007 Grand Vitara 2,0 with fault codes c1037 and c1028, can you send me a qoutation and an explanation of your workway on this problem? Thanks in advance. Best regards, Jorn. Located in the netherlands.

    • Hi Jorn

      Thanks for the enquiry,

      We’ve sent you an email with pricing to repair your Suzuki Grand Vitara ABS module and information on how to send the unit to us from the Netherlands.

      Kind Regards

      Jason
      SINSPEED

  • Hi guys, I live in Australia, my 2010 Grand vitara which Has ABS light and ESP service in display, codes state c1061, i have replaced the battery and Cleared codes, but c1061 returns, couldnthis be a faulty ABS pump

    Thanks

    • Hi Nathan

      Thanks for the enquiry,

      It definitely could be a faulty ABS pump as we’ve seen this fault many times, it’s a very common code relating to a failure within the ABS Pump motor circuit / motor driver fault. It’s a fault we’re able to permanently rectify with a Lifetime warranty.

      I have sent you an email with full pricing and information.

      Kind Regards

      Jason
      SINSPEED

  • 07 SUZUKI ESCUDO Brake Pressure Sensor Switch Failure
    PARTS NUMBER 06-2109-5102.3
    HOW MUCH REPAIR AND FRIGHT FROM NZ ?
    THANKS

    • Hi George

      Thanks for the enquiry,

      We’ve sent you an email with full pricing and information.

      Kind Regards

      Jason
      SINSPEED

  • Hi, I have a 2009 Suzuki Grand Vitara. Abs Failure can you qoute me a price. With return shipping to Manati, Puerto Rico 00674 USA. Thanks.

    • Hello Anthony

      Thank you for your enquiry, and many apologies for the delay in our response.

      I have sent you an email now for some further information regarding the reapir of your Suzuki ABS Pump. Please reply to the email with the fault code and we will be able to confirm if it is repairable.

      Kindest Regards

      Jason
      Sinspeed

  • Hi, I have a 2010 Suzuki Grand Vitara. Abs Failure can you qoute me a price. With return shipping to Arecibo, Puerto Rico 00612 USA. Thanks.

    • Hello Alicia,

      Thank you for your enquiry

      We have sent over an email now for further information regarding the fault, and once the reply has been received, will be able to quote accordingly.

      Kind Regards

      Jason
      SINSPEED

  • I have a 2010 Suzuki grand vitara in which my abs, esp, and brake light are on in the instrument cluster. The code is c1044 in which appears to be related high pressure senor. How much would it cost to fix my abs pump? and how long will It take?

    Thank you

    • Hello Juan,

      Thank you for your enquiry,

      We have emailed accross pricing and further information regarding this query. Please do not hesitate to come back to us if you require any further information.

      Kind Regards,

      Jason
      SINSPEED

    • Hi Edwin

      Thanks for the enquiry and many apologies for the delay in our response.

      We’ve sent you an email with pricing and information.

      Kind Regards

      Jason
      SINSPEED

    • Hi Darryn,

      Thanks for the enquiry and many apologies for the delay in our response.

      It’s a very common issue and one we can definitely get sorted for you. We’ve sent over an email now with full pricing and some further information.

      Kind Regards

      Jason
      SINSPEED

Leave a Reply

Your email address will not be published. Required fields are marked *

Contact